Sony PetaSite DMS-B110S Installation Manual Download Page 58

Page: 58 / 112

6-32

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

Fix the cable relay plate (EXD) to the second exten-
sion console with the three screws (PWH 4

8).

Route the five types of cables under the EX stage
support and extend them to the basic console.

Attach the flat cable connector to the floor of the first
extension console with the two screws (PS3

10)

Install the four locking adjust clamps to the first
extension console.

PWH4

Cable relay plate (EXD)

Locking adjust clamp

PS3

Locking adjust clamp

Flat cable

Connect the five types of cables to the mating cables
of the basic console.

Fix the four types of cables with the six locking adjust
clamps.

10. Attach the SV cable cover (EXD1) with the two

screws (PWH4

8). (The first and the second exten-

sion console)

Be careful not pinch the cables and harnesses with the
edge of the SV cable cover (EXD1).

Locking adjust clamps

SV cable covers (EXD1)

PWH4

6-6. Installation of DMSA-CBL1

Summary of Contents for PetaSite DMS-B110S

















































































































Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands

Sony PetaSite DMS-B110S, Installation Manual

Search results

Summary of Contents for PetaSite DMS-B110S

Reviews:

Related manuals for PetaSite DMS-B110S

Brands by name

Popular brands