manualshive.com logo in svg

Sonnen sonnenBatterie 10, Installation Instructions Manual, Page: 76 / 100

Share
Download
Sonnen sonnenBatterie 10 Installation Instructions Manual Download Page 76

10 | Completing installation

76 / 100

Installation instructions sonnenBatterie 10

10 Completing installation

10.1 Filling out the type plate

Tools:

• Permanent marker

The energy capacity marked on the type plate always refers to the total energy
installed in the storage system and extension cabinet, if any.

„

Mark the installed battery capacity on the type plate, which is affixed to the switch
panel of the storage system.

The possible battery capacities with the associated nominal power values can be found in
section Technical data [P. 89].

10.2 Attaching and earthing the cover

• The earth connection between the cover and mounting frame is established via the

screw connection.

• The inspection window and sonnen Eclipse have protective film on the inside and out-

side.

„

Remove all protective film before mounting the cover.

1.

3.

2.

„

Tilt the cover forward when lifting it, so it can be hung on the mounting frame.

„

Centre and then hang the cover on the mounting frame. 

WARNING! Do not kink or

crush any cables between the cover and the mounting frame.

Summary of Contents for sonnenBatterie 10





































































































Reviews:

No comments