SMC Networks 8926EM Management Manual Download Page 744 | Manualshive

Page: 744 / 792

background image

IP Routing Commands

42-28

42

Command Mode

Router Configuration

Default Setting

No stub is configured.
Summary advertisement are sent into the stub.

Command Usage

• All routers in a stub must be configured with the same area ID using this

command.

• Routing table space is saved in a stub by blocking Type-4 AS summary LSAs

and Type 5 external LSAs. The no-summary option can be used to completely
isolate the stub by blocking Type-3 summary LSAs that advertise the default
route for destinations external to the local area or the autonomous system.

• Use the no-summary parameter of this command on the ABR attached to the

stub to define a totally stubby area. Define an area as a totally stubby area
only if routers in the area do not require summary LSAs from other areas.

• Use the

area default-cost

command to specify the cost of a default summary

route sent into a stub by an ABR.

• This router supports up to 16 total areas (either normal transit areas, stubs, or

NSSAs).

Example

This example creates a stub area 10.2.0.0, and assigns all interfaces with class B
addresses 10.2.x.x to the stub.

Related Commands

area default-cost (42-24)

area nssa

This command defines a not-so-stubby area (NSSA). To remove an NSSA, use the

no

form without any optional keywords. To remove an optional attribute, use the

no

form without the relevant keyword.

Syntax

[

no

]

area

area-id

nssa

[

no-redistribution

] [

default-information-originate

]

•

area-id

- Identifies the NSSA.

(The area ID must be in the form of an IPv4 address.)

•

no-redistribution

- Use this keyword when the router is an NSSA Area

Border Router (ABR) and the

redistribute

command is required to import

routes only into normal areas, and not into the NSSA. In other words, this
keyword prevents the NSSA ABR from advertising external routing
information (learned via routers in other areas) into the NSSA.

Console(config-router)#area 10.2.0.0 stub
Console(config-router)#network 10.2.0.0 0.255.255.255 area 10.2.0.0
Console(config-router)#

«
...
742
743
744
745
746
...
»

Summary of Contents for 8926EM

























































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8926EM

Brand: Barco Pages: 6

Brand: Xantech Pages: 20

Brand: National Instruments Pages: 32

Brand: Black Box Pages: 26

M800 Elite Series

Brand: 4B Pages: 12

Brand: DITEC Pages: 8

Champion KD-2X1

Brand: Key Digital Pages: 12

Brand: LEGRAND Pages: 12

Brand: Optical Systems Design Pages: 20

Brand: WIKA Pages: 8

3C17205 - SuperStack 3 Switch 4400 PWR

Brand: 3Com Pages: 90

BNI EIP-950-000-Z009

Brand: Balluff Pages: 12

Magnum CS14 Series

Brand: GarrettCom Pages: 76

Brand: AbleNet Pages: 6

Brand: Pakedge Pages: 12

Brand: ADS Technologies Pages: 2

Brand: hager Pages: 72

Brand: LevelOne Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands