manualshive.com logo in svg

SMC Networks 8926EM, Management Manual

Share
Download
SMC Networks 8926EM Management Manual Download Page 173

Configuring Access Control Lists

7-9

7

•

Destination Prefix-Length

 – A decimal value indicating how many contiguous bits 

(from the left) of the address comprise the prefix (i.e., the network portion of the 
address).

•

Next Header

 – Identifies the type of header immediately following the IPv6 header. 

(Range: 0-255)
Optional internet-layer information is encoded in separate headers that may be 
placed between the IPv6 header and the upper-layer header in a packet. There are 
a small number of such extension headers, each identified by a distinct Next 
Header value. IPv6 supports the values defined for the IPv4 Protocol field in RFC 
1700, and includes these commonly used headers:
0 :  Hop-by-Hop Options 

(RFC 2460)

6 :  TCP Upper-layer Header 

(RFC 1700)

17:  UDP Upper-layer Header 

(RFC 1700)

43: Routing 

(RFC 2460)

44: Fragment 

(RFC 2460)

51: Authentication 

(RFC 2402)

50:  Encapsulating Security Payload 

(RFC 2406)

60:  Destination Options 

(RFC 2460)

•

DSCP

 – DSCP priority level. (Range: 0-63)

•

Flow Label

 – A label for packets belonging to a particular traffic “flow” for which 

the sender requests special handling by IPv6 routers, such as non-default quality 
of service or “real-time” service (see RFC 2460). (Range: 0-16777215)
A flow label is assigned to a flow by the flow's source node. New flow labels must 
be chosen pseudo-randomly and uniformly from the range 1 to FFFFF 
hexadecimal. The purpose of the random allocation is to make any set of bits within 
the Flow Label field suitable for use as a hash key by routers, for looking up the 
state associated with the flow.
A flow identifies a sequence of packets sent from a particular source to a particular 
(unicast or multicast) destination for which the source desires special handling by 
the intervening routers. The nature of that special handling might be conveyed to 
the routers by a control protocol, such as a resource reservation protocol, or by 
information within the flow's packets themselves, e.g., in a hop-by-hop option. A 
flow is uniquely identified by the combination of a source address and a non-zero 
flow label. Packets that do not belong to a flow carry a flow label of zero. 
Hosts or routers that do not support the functions specified by the flow label must 
set the field to zero when originating a packet, pass the field on unchanged when 
forwarding a packet, and ignore the field when receiving a packet. 

Summary of Contents for 8926EM

























































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands