IEEE 802.1Q VLANs
11-11
11
types, any received frames that are untagged are assigned to the default VLAN.
(Option: All, Tagged; Default: All)
•
Ingress Filtering
– Determines how to process frames tagged for VLANs for which
the ingress port is not a member. (Default: Disabled)
- Ingress filtering only affects tagged frames.
- If ingress filtering is disabled and a port receives frames tagged for VLANs for
which it is not a member, these frames will be flooded to all other ports (except
for those VLANs explicitly forbidden on this port).
- If ingress filtering is enabled and a port receives frames tagged for VLANs for
which it is not a member, these frames will be discarded.
- Ingress filtering does not affect VLAN independent BPDU frames, such as GVRP
or STP. However, they do affect VLAN dependent BPDU frames, such as GMRP.
•
GVRP Status
– Enables/disables GVRP for the interface. GVRP must be globally
enabled for the switch before this setting can take effect. (See "Displaying Bridge
Extension Capabilities" on page 4-4.) When disabled, any GVRP packets received
on this port will be discarded and no GVRP registrations will be propagated from
other ports. (Default: Disabled)
•
GARP Join Timer
13
– The interval between transmitting requests/queries to
participate in a VLAN group. (Range: 20-1000 centiseconds; Default: 20)
•
GARP Leave Timer
13
– The interval a port waits before leaving a VLAN group.
This time should be set to more than twice the join time. This ensures that after a
Leave or LeaveAll message has been issued, the applicants can rejoin before the
port actually leaves the group. (Range: 60-3000 centiseconds; Default: 60)
•
GARP LeaveAll Timer
13
– The interval between sending out a LeaveAll query
message for VLAN group participants and the port leaving the group. This interval
should be considerably larger than the Leave Time to minimize the amount of traffic
generated by nodes rejoining the group.
(Range: 500-18000 centiseconds; Default: 1000)
•
Mode
– Indicates VLAN membership mode for an interface. (Default: Hybrid)
-
1Q Trunk
– Specifies a port as an end-point for a VLAN trunk. A trunk is a direct
link between two switches, so the port transmits tagged frames that identify the
source VLAN. Note that frames belonging to the port’s default VLAN (i.e.,
associated with the PVID) are also transmitted as tagged frames.
-
Hybrid
– Specifies a hybrid VLAN interface. The port may transmit tagged or
untagged frames.
•
Trunk Member
– Indicates if a port is a member of a trunk. To add a trunk to the
selected VLAN, use the last table on the VLAN Static Table page.
13. Timer settings must follow this rule: 2 x (join timer) < leave timer < leaveAll timer
Summary of Contents for 8926EM
