manualshive.com logo in svg

SMC Networks 8926EM, Management Manual

Share
Download
SMC Networks 8926EM Management Manual Download Page 325

Configuring IP Routing Interfaces

19-5

19

Web -

 Click IP, General, Global Settings. Set IP Routing Status to Disabled to restrict 

operation to Layer 2, or Enabled to allow multilayer switching, specify the default 
gateway which will be forwarded packets for all unknown subnets, and click Apply.

Figure 19-1   IP Global Settings

CLI -

 This example enables IP routing, and sets the default gateway.

Configuring IP Routing Interfaces

You can specify the IP subnets connected to this router by manually assigning an 
IP address to each VLAN, or by using the RIP or OSPF dynamic routing protocols to 
identify routes that lead to other interfaces by exchanging protocol messages with 
other routers on the network. 

Once IP interfaces have been configured, the switch functions as a multilayer 
routing switch, operating at either Layer 2 or 3 as required. All IP packets are routed 
directly between local interfaces, or indirectly to remote interfaces using either static 
routing or dynamic routing. All other packets for non-IP protocols (for example, 
NetBuei, NetWare or AppleTalk) are switched based on MAC addresses.

Command Usage

• If this router is directly connected to end node devices (or connected to end nodes 

through shared media) that will be assigned to a specific subnet, then you must 
create a router interface for each VLAN that will support routing. The router 
interface consists of an IP address and subnet mask. This interface address 
defines both the network prefix number to which the router interface is attached 
and the router’s host number on that network. In other words, a router interface 
address defines the network segment that is connected to that interface, and 
allows you to send IP packets to or from the router.

Console(config)#ip routing

42-1

Console(config)#ip route default 10.1.0.254

42-2

Console(config)#

Summary of Contents for 8926EM

























































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands