Section 05
TRANSMISSION
Sub-Section 03
(DRIVEN PULLEY)
05-03-5
I
MPORTANT :
Large bushing retaining screws
and washers must be removed before small
bushing installation.
Coat bushing outside diameter with Loctite 609
(P / N 413 7031 00).
Install bushing as following photo.
ASSEMBLY
4, Cam Slider Shoe
When replacing slider shoes, always install a new
set (3 shoes) to maintain equal pressure on the
cam.
Assemble driven pulley components by reversing
the disassembly procedure.
18, Cam
Coat cam interior with anti-seize lubricant.
INSTALLATION
14,15, Countershaft and Anti-seize
Lubricant
CAUTION : Always apply anti-seize lubri-
cant (P / N 413 7010 00) on the counter-
shaft before final pulley installation.
F-Series and S-Series Only
Should installation procedure be required, refer to
BRAKE 05-05 then look for
Brake Disc
and
Coun-
tershaft Bearing Adjustment
.
Reinstall the pulley on the countershaft by revers-
ing the removal procedure.
All Models
Check end play of driven pulley on countershaft
by pushing pulley towards outer housing so that
the inner shims (P / N 504 1082 00) contact it.
Measure end play at the mounting screw end be-
tween shim(s) and pulley. See illustration.
TYPICAL
1. Shim (P / N 504 1082 00) (as required)
2. Contact
A. 0 to 1 mm (0 to 3/64 in)
13, Pulley Retaining Screw
Torque to 25 N•m (18 lbf•ft).
ADJUSTMENT
Refer to PULLEY DISTANCE AND ALIGNMENT
05-04 to adjust pulley distance. Adjust drive belt
height between pulley halves to obtain specified
belt deflection.
A03D1YA
529 0313 00
529 0312 00
A03D1ZA
529 0313 00
529 0312 00
-
A16D0IA
1
2
A
1
Summary of Contents for FORMULA III
