Silverline Fall Arrest Harness, Manual

Page: 6 / 48

6
GB
• Use the Sternal Attachment Point (A/2) (8) to connect to a mobile fall arrester
and other rope access systems according to EN363
Clearance
• Fall clearance:
Before use, it is essential to verify the
clearance required beneath the user. This
clearance must be sufficient to prevent the
user from hitting the ground or another
obstacle, in the event of a fall (see Fig. I)
• Swing falls:
WARNING: The force of striking an
object in a swing fall may cause serious
injury or death.
Swing falls occur when the anchorage is
not located directly above the point where
a fall occurs (see Fig. J). Minimise swing
falls by working as close as possible to the
anchorage. DO NOT enter a situation where
a swing fall could occur, if it is likely to
result in an injury
Note: The risk of swing falls significantly
increases the clearance required when
using a self-retracting lifeline or another
variable length connecting system.
WARNING: When connectors are
poorly positioned, the attachment D-rings
could act as a lever on the gate of a
karabiner and subsequently damage it
when sudden tension comes on to the
rope. ALWAYS ensure connectors remain
safely positioned during use.
Compatibility
• This harness is compatible with miscellaneous fall arrest systems and safety
gear, including but not limited to the following Silverline products:
• 253162 Shock Absorbing Lanyard
• 253600 Karabiner
Notes:
• Connecting hardware must be compatible in size, shape, and strength.
Non-compatible connectors may accidentally disengage and lead to serious
injury or even death
• Only use connectors, such as D-rings, snaphooks, karabiners and other
equipment with a minimum rating of 22kN
WARNING: Always verify that all components used in combination with each
other are compatible.
Anchorage requirements
Fig. K
• The minimum strength of any anchorage must be 10kN, according to EN795
• Check anchorage for signs of deterioration
• As with all fall arrest gear, anchorages must be subjected to regular
inspections by a competent person. Inspect at least once every three months
and record findings in a dedicated service record
• Check that the karabiner is the correct size for the anchorage to be used. If the
karabiner is too small, use an anchor sling to connect to the anchorage
Anchorage position
• The anchorage of the system should preferably be located above the user’s
position
Use as part of a fall arrest system
• Anchorages selected for fall arrest systems should be capable of sustaining a
static load, applied in the directions permitted by the system of at least:
• 22kN for non-certified anchorages
• 2 x the maximum arrest force for certified anchorages
• If more than one system is attached to one anchorage, the required
strength should be multiplied by the number of systems attached
Removing the harness
1. Ensure you are located in a safe place away from any fall hazards
2. Open both Leg Strap Buckles (6) by passing the three-bar slide through the
square link
3. Open the Chest Strap (2) buckle
4. Remove your arms from the harness
Note: Inspect the harness after use, and follow instructions for cleaning,
disinfection, transport and storage as outlined in ‘Maintenance’.
Operation
Note: This equipment must ONLY be used by competent operators. All users
must be trained in its safe use. Inexperienced users must receive instruction
prior to using this equipment. A risk assessment must be carried out before
undertaking any operations requiring fall arrest equipment.
WARNING: ALWAYS wear personal protective equipment appropriate for the
work area and type of activity, including but not limited to, eye protection, gloves,
hard hat, protective shoes and hearing protection.
Note: Check the correct fitting and adjustment at least every 2 hours during use.
This may save your life!
Regularly check connections with other equipment in
the system, and ensure various system components are correctly positioned with
respect to each other.
Rescue plan
WARNING: A suitable and sufficient risk assessment must be carried out
before commencing with any kind of work at height, or any work that requires
the use of personal protective equipment (PPE) as a control measure.
• The user must have a rescue plan and the means at hand to implement it
• The plan must take into account the equipment and special training necessary
to effectively conduct prompt rescue under all foreseeable conditions
Accessories
• Additional fall arrest gear, workwear and other personal protection equipment
is available from your Silverline stockist
Maintenance
Note: All fall arrest equipment must be regularly inspected, cleaned and
maintained by a competent person, in accordance with local laws and
regulations. Maintenance must be recorded in a dedicated service record (see
end of this manual).
WARNING: Carry out a visual and tactile inspection of all components every
time the equipment is used. Carry out a detailed examination if the equipment
has not been used for some time. Note: A thorough, detailed examination of
the equipment must be carried out at regular intervals, at least once annually, or
more frequently depending on use.
WARNING: It is ILLEGAL to carry out any kind of repair or modification to
this equipment.
WARNING: Should any damage be detected, remove the equipment from
service immediately. It must then be rendered unusable and discarded.
Visual/tactile inspection
The following defects potentially result in degradation and/or weakening of
equipment components:
Fig. J
Swing
Fall
Hazard
Fig. I
6.75m 2m
2m
Maximum
1.5m
1m
250482_Manual.indd 6 04/01/2018 16:21