Siemens SIMATIC PCS 7 SMART Getting Started Download Page 87

Page: 87 / 210

Block

Block name in

the project

I/O

Meaning

Value

SP.Value

Active flow setpoint

70.0

SP_Ext.Value

External manipulated value 120.0

SP_ExtAct.Value

Active external setpoint

SP_HiLim.Value

Coarse dosing: High limit

setpoint flow

70.0

SP_Int

Coarse dosing setpoint

70.0

SP_LiOp.Value

1=Linking, 0=Operator Ac‐

tive

SP_TrkExt

1 = Bumpless switchover

from external to internal set‐

point active

SP2_Ext.Value

Fine dosing external set‐

point

15.0

SP2_HiLim.Value

Fine dosing: High limit set‐

point flow

15.0

SP2_Int

Fine dosing setpoint

9.0

TI.Value

Reset time

30.0

Mul04

MUL

In2.Value

Value to be multiplied

In3.Value

The value to be multiplied

(value as percentage)

0.01

PIDConL

CTRL_PID

AutModLi.Value

Interconnection to automat‐

ModLiOp.Value

Interconnection automatic/

manual active

MV_HiLim.Value

High limit for manipulated

value

99.0

PV_AH_Lim

Process value alarm: High

limit

70.0

PV_AH_En

1 = Enable PV alarm limit

(high)

PV_AL_En

1 = Enable PV alarm limit

(low)

PV_WH_En

1 = Enable PV warning limit

(high)

PV_WL_En

1 = Enable PV warning limit

(low)

PV_TH_En

1 = Enable PV alarm limit

(high)

PV_TL_En

1 = Enable PV alarm limit

(low)

PV_OpScale.High

Process value: High scale

limit of bar graph

70.0

SP_Ext.Value

External manipulated value 70.0

SP_ExtLi.Value

Interconnection for the in‐

ternal/external switchover

active

Creating CFCs

6.6 Working with the CFC Editor

PCS 7 SMART Getting Started - Part 1 (V9.0 with APL)

Getting Started, 12/2017, A5E42181435-AA

Summary of Contents for SIMATIC PCS 7 SMART



















































































































































































































Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands

Siemens SIMATIC PCS 7 SMART, Getting Started

Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands