Siemens SIMATIC PCS 7 SMART Page 197 Getting Started Download

Page: 197 / 210

Starting and adapting the color_gs project

12.1

color_gs project

Downloading the color_gs project

You can download the completely configured PCS 7 SMART color_gs project from the Internet

(

https://support.industry.siemens.com/cs/in/en/view/109478794

Use this project to gain an insight into working with SIMATIC PCS 7 SMART or to compare

the project you have created with this color_gs project.
You can open and start this project on your computer. Since we assumed a specific hardware

configuration when creating the project, you will need to adapt the hardware configuration if

you use different hardware components.
The overview shows you how to open and adapt the color_gs project:
● Open the color_gs project (Page 198)
● Adapt the hardware of the color_gs project (Page 198)
● Adapt the blocks for the color_gs project (Page 199)
● Adapt the project data for the color_gs project (Page 200)
● Compile and download the color_gs project (Page 201)

PCS 7 SMART Getting Started - Part 1 (V9.0 with APL)

Getting Started, 12/2017, A5E42181435-AA

197

Summary of Contents for SIMATIC PCS 7 SMART



















































































































































































































Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands

Siemens SIMATIC PCS 7 SMART, Getting Started

Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands