Siemens IM 328-N Description Download Page 45

Page: 45 / 86

07.96

Description

3-17



SINUMERIK 805SM / 840C (BS)

.
.
.

Call

diagnostics

Read

diagnostics

.
.
.

Diagnostics word

Diagnostics data

Fig. 3-8

Request and read diagnostics

For the slave IM 328–N the following diagnostics are of considerable
importance:

Station status

Device–oriented diagnostics (station diagnostics)

The diagnostics are loaded and transferred with the following instructions:

L KY (station number), (code)

Station number 3 to 124
Code: 0 to 7

T PW 252

After that, the station diagnostics are
transferred to the diagnostics word

Eight words in each slave station are reserved for station status, device–
oriented (station diagnostics) and ID–oriented diagnostics (module
diagnostics).

Code

Diagnostics address

Diagnostics a 1

Station status 1

Station status 2

Station status 3

Master address

Manufacturer ID

Header

Device–oriented diagnostics

(station diagnostics)

Header

ID–oriented diagnostics

(module diagnostics)

Unused

Important
diagnostics for
IM 328–N, slave

Structure and
requesting
diagnostics

3.2 Description of the DP standard slaves

Summary of Contents for IM 328-N























































































Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands

Siemens IM 328-N, Description

Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands