Siemens IM 328-N Description Download Page 36

Page: 36 / 86

07.96

Description

3-8

6ZB5 430–0BH02–1AA0



SINUMERIK 805SM / 840C (BS)

3.2.3

Procedure for Installation and Startup

The following procedure is recommended for installation and startup of a
station with an IM 329-N, DP slave:

Set and check the following data on the module in accordance with
Section 2.1.1:

–

Control type

–

Address range (number of input and output bytes)

–

Base address

Install the module in the control:

–

Switch off the control

–

Plug the module into a valid slot, see information for the relevant
control in

Reference:

/3/, SINUMERIK 805SM,

Interface Description Part 2 – Connection Conditions

Reference:

/4/, SIROTEC ACR 20, Configuring Guide

Reference:

/5/, SINUMERIK 840C

Interface Description Part 2 – Connection Conditions

–

Set the station address on the front panel in accordance with
Section 2.1.2.

–

Connect the module to the SINEC L2-DP field bus

–

Switch on the control (POWER ON) and perform a RESTART of the
PLC if required

Note

On the SINUMERIK 840C, I/O modules that have just been slotted in are
not recognized until a cold RESTART of the control is performed.

Modify the configuration of the master (e.g. IM 308-B):

–

Add the configuration data of the new station to the existing program
file

–

For the IM 308–B: Write to the memory module
For the IM 329–N, master: perform DOWNLOAD

Reference:

/7/, SIROTEC ACR20, SINUMERIK 805SM/840C

Link to SINEC L2–DP with module IM 329–N

–

Program and activate monitoring and diagnostics functions on the
master and slave sides.

3.2 Description of the DP standard slaves

Summary of Contents for IM 328-N























































































Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands

Siemens IM 328-N, Description

Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands