Siemens IM 328-N Description Download Page 80

Page: 80 / 86

07.96

Description

3-21



SINUMERIK 805SM / 840C (BS)

FEPROM

Flash EPROM: read and write memory (non–volatile me-

mory)

GND

Signal ground, reference point

HEX

Abbreviation for a hexadecimal number

IM 308–B

Master interface module

IM 318–B

Interface module for slave station Et 200U

IM 328–N

Slave module for fieldbus SINEC L2–DP

IM 329–N

Slave and master module for fieldbus SINEC L2–DP

LED

Light emitting diode

Organization block

PIQ

Process output image

PII

Process input image

Peripheral byte

Programming unit

PROFIBUS

PROcess Field BUS, German process and fieldbus standard defined in the
PROFIBUS standard (DIN 19245).
This standard defines functional, electrical and mechanical characteristics for
bit–serial fieldbus systems.

((S. A–3))

PROFIBUS–DP

Standard proposal PROFIBUS–DP (DIN E 19245, Part 3) on which the distri-
buted I/O system ET 200 is based

I/O word

Timeout

RAM

Random Access Memory

SPS

Standard plug–in station (1 SPS = 15–24 mm)

SINEC L2

Bus system: Networked PROFIBUS–compatible programmable control system
and field devices on the cell and field level.

SINEC L2–DP

Bus system SINEC L2 with DP protocol (stands for distributed peripherals)

Softkey

SPC

Serial Periphery Controller

SRAM

Static RAM (buffered)

Station number

Each ET 200 bus node is assigned a unique station number

SWx

Software Version x

Summary of Contents for IM 328-N























































































Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands

Siemens IM 328-N, Description

Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands