Siemens IM 328-N Description Download Page 79

Page: 79 / 86

07.96

Description

3-20

6ZB5 430–0BH02–1AA0



SINUMERIK 805SM / 840C (BS)

((Rest der S. von alter S. 3–21, ohne Änderungen (bis auf gelb markierte Än-
derung) übernehmen))

((Titel ”Example” fällt auch weg))

((S. A–1))

((alphabetisch ordnen: ))

Output byte

PLC

Programmable controller

COM

Communication

COM ET 200

Communications software for configuring the master inter-

face module

CPU

Central Processing Unit

CP 5410–S5DOS/ST

PG interface module for connection to SI-

NEC L2 and/or SINEC L2–DP

Digital outputs

Data block

Digital inputs

Download

Loading the master configuration onto the DP master via

SINEC L2–DP bus

Distributed I/Os

DP master

e.g. IM 308–B, IM 329–N

DP standard

Procedure acc. to PROFIBUS–DP (DIN E 19245, Part3)

DPR

DUAL–PORT RAM, memory that can be accessed both

ways (read and write access)

Data word

Input byte

ET 200

Electronic Terminator 200, distributed I/O system 200

((S. A–2))

ET 200B

Distributed I/O device to degree of protection IP 20, small and compact, there-
fore suitable if only a few inputs/outputs are required or if available mounting
depth is small.

ET 200C

Distributed I/O device, compact design to degree of protection IP 65, for use in
an industrial environment

ET 200U

Distributed I/O device, modular design to degree of protection IP 20, for uni-
versal applications especially in intelligent modules

Function block

FMS

Fieldbus Message Specification

Summary of Contents for IM 328-N























































































Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands

Siemens IM 328-N, Description

Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands