Siemens IM 328-N Description Download Page 42

Page: 42 / 86

07.96

Description

3-14

6ZB5 430–0BH02–1AA0



SINUMERIK 805SM / 840C (BS)

3.2.5

Status display messages

Normal operating state

Normal operation is displayed via the status display as follows:

RUN

(green LED)

FAULT

(red LED)

Meaning

off

Normal operation, slave is in cyclic mode

Fault during data transmission

The following faults are possible in data transmission:

Slave disconnected from the bus (e.g. bus connector unplugged)

Master broken down or switched off

Configuration of the slave does not correspond to the configuration data
of the master

If threshold monitoring (system parameter) is activated, a fault in data trans-
mission (i.e. a bus fault) is displayed by the STATUS DISPLAY SLAVE as
follows:

RUN

(green LED)

FAULT

(red LED)

Meaning

Fault during data transmission

Reset of the inputs implemented by the slave in the slave station.

Cyclic attempt of the module to link to the SINEC L2-DP bus.

Warning

If no response monitoring is activated, the inputs of the station concerned are
also not reset if a fault occurs but they remain unchanged.

Status display
slave

Effects of fault

3.2 Description of the DP standard slaves

Summary of Contents for IM 328-N























































































Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands

Siemens IM 328-N, Description

Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands