Siemens IM 328-N Description Download Page 22

Page: 22 / 86

07.96

Description

2-10

6ZB5 430–0BH02–1AA0



SINUMERIK 805SM / 840C (BS)

2.2.1

Jumper settings

The module can be used in the control systems listed. The control type must
be set with switches S1, S5.1, S5.2 and S5.3 as follows:

S5.1

S5.2

S5.3

SINUMERIK 805SM

closed

open

closed

open

SIROTEC ACR 20

closed

SINUMERIK 840C

closed

Note

The IM 328–N module can only be used for SINUMERIK 805SM in the
central controller.

Switches S2.1 and S2.2 must be set according to the table below in order to
set the address range of 4, 8, 16 or 32 input or output bytes.

Address range

S2.1 in position

S2.2 in position

4 bytes

open

8 bytes

closed

open

16 bytes

open

closed

32 bytes

closed

Note

Address range of, for example, 4 bytes means that 4 input bytes and 4 output
bytes are available with the same base address.

The following switches are used to set the base address:

S3.1 to S3.8

for an address range of

4 bytes

S3.2 to S3.8

for an address range of

8 bytes

S3.3 to S3.8

for an address range of

16 bytes

S3.4 to S3.8

for an address range of

32 bytes

Selecting the
control system
(S1, S5.1, S5.2 and
S5.3)

Setting of address
range (number of
input and output
bytes) (S2.1 and
S2.2)

Setting the base
address
(S3.1 to S3.8)

2.2 Hardware of the module 6FC5 012–0CA01–0AA0

Summary of Contents for IM 328-N























































































Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands

Siemens IM 328-N, Description

Search results

Summary of Contents for IM 328-N

Reviews:

Related manuals for IM 328-N

Brands by name

Popular brands