Siemens HiPath 4000 Operating Manual Download Page 25

Page: 25 / 135

Putting the handset into service

Removing the protective cover

Ex protection and IP rating compliance

(Ex protection only applies to Gigaset M2 Ex professional)

Inserting the battery compartment seal

Insert the battery compartment seal carefully (around the battery compart-

ment).

Inserting the plug into the charging socket

Insert the plug into the Slim Lumberg jack on the underside of the handset.

Only remove the plug when charging the handset, connecting a wired

headset or connecting a data transfer cable.

Removing this plug cancels the Ex protection and IP rating.

The hand-

set should only be operated in this condition in permitted zones.

Remove the protective cover from the display before

putting the handset into service.

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands