Siemens HiPath 4000 Operating Manual Download Page 68

Page: 68 / 135

Step by Step

Conducting calls – enhanced functions

Dialling after (successful) identification:

You will hear the dialling tone. The following appears on

the display:

"Please dial".

Enter a phone number.

Call forwarding - follow me after successful identi-

fication:

> <

[

Select the menu item and confirm.

[

Confirm. Call forwarding is activated immediately.

Suppressing call ID display for called
party

The call ID display can only be suppressed for one sub-

sequent call and the setting is not saved if the number

is redialled.

Call the system menu.

> <

[

Select and confirm the basic service.

> <

[

Select the menu item and confirm.

> <

[

Select the menu item and confirm.

Enter the phone number of the user. If the extension ac-

cepts the call, your phone number will not be displayed.

VARY FORWARD

SAVE

BASIC SERVICE

OTHER FUNCT.

NO DISPLAY

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands