Siemens HiPath 4000 Operating Manual Download Page 30

Page: 30 / 135

Putting the handset into service

Battery pack operating times and charging time

The operating times are only achieved after several charging and discharg-

ing cycles.

The handset’s standby time is significantly increased by deactivating the

backlight.

Permitted battery packs

Only the original Siemens battery pack is permitted for the handset.

Capacity (mAh)

Stand-by mode

(hours)

Talk time

(hours)

Charging

time

(hours)

1000

(original battery pack)

approx. 380 (16 days),

prerequisite: no back-

light

approx. 12

approx. 3.7

Battery pack

Part number

For Gigaset M2 professional:

Lithium-Ion, 1000 mAh

A5B00075416005

For Gigaset M2 Ex professional:

Lithium-Ion, 1000 mAh, with additional electron-

ics

A5B00075609027

Danger of explosion:

Local and operational factors may lead to an explosive atmosphere

in an Ex zone. Never open the handset battery compartment in an

Ex zone.

Attention:

For Gigaset M2 Ex professional:

Only use approved Ex battery

packs (see the "Approved Battery Packs" section in the operating

manual). Ex authorisation is only valid and the handset can only be

operated if this battery pack is installed. Other battery packs are

strictly prohibited. If they are used, Ex protection is no longer valid.

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands