Siemens HiPath 4000 Operating Manual Download Page 75

Page: 75 / 135

Conducting calls – enhanced functions

Step by Step

Output on first line.

> <

[

Confirm to select the next variable forwarding type.

> <

To edit the current variable forwarding type, select the

required command.

Programming a forwarding destination

Open the system menu.

> <

[

Select and confirm the basic service.

> <

[

Select the menu item and confirm.

[

Confirm. "VARY FORWARD" is displayed.

[

Confirm. "FIXED FORWARD" is displayed.

[

Confirm. "Forw. for internal" is displayed.

> <

[

Select and confirm.

Enter the phone number for the forwarding destination.

Any destination previously programmed will be over-

written.

[

Confirm when the complete number has been entered.

To select a different forwarding type, proceed as de-

scribed on

Page 64.

If variable forwarding was previously programmed and

activated, it is deactivated and the forwarding destina-

tion is deleted ((for exception, see

Page 64). Fixed

forwarding is deactivated.

Deleting a forwarding destination

A variable forwarding destination is automatically delet-

ed when the forwarding type is deactivated.

Activating variable forwarding

Variable forwarding is automatically activated when the

forwarding destination is programmed.

Forw. for external

BASIC SERVICE

DESTINATIONS

FORWARD

ENTER DESTIN.:

SAVE

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands