Siemens HiPath 4000 Operating Manual Download Page 98

Page: 98 / 135

Step by Step

Additional functions

Save the settings.

The alarm clock is activated.
Press the On-hook key to end the operation.

Deactivating an alarm/repeating after a pause

The alarm rings for 60 seconds. The following appears

on the display:

. If you do not press anything, the

alarm repeats after five minutes and then deactivates.

During the alarm:

either:

Press the display key. The alarm deactivates.

or:

Press the display key or any key. The alarm deactivates

and is repeated after five minutes. The alarm is repeat-

ed twice and then permanently deactivated.

Deactivating the alarm clock

The handset is in idle status.

Open the main menu of the handset.

[

Select the menu item and confirm. The input mask for

setting the alarm is displayed.

Activation:

Off

Define the setting.

Save setting.
Press the On-hook key to end the operation.

Save

Off

Snooze

Alarm Clock

Save

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands