Siemens HiPath 4000 Operating Manual Download Page 92

Page: 92 / 135

Step by Step

Conducting calls – with multiple users

> <

[

Select and confirm to end the display.

or:

> <

[

Select and confirm to disconnect this member from the

conference. If there were only three members, the con-

ference is now ended.

Disconnecting the last member added

You wish to disconnect the last member added to the

conference.

> <

[

Select and confirm. The last member added is discon-

nected. If there were only three members, the confer-

ence is now ended.

Using the camp-on function

If you are expecting an important call, you should acti-

vate the camp-on function. A second call will then be

signalled while a call is in progress. You can accept or ig-

nore the second call.

Activating and deactivating the camp-on function

Call the system menu.

> <

[

Select and confirm the basic service.

> <

[

Select the menu item and confirm.

> <

[

Select the menu item and confirm.

Activating or deactivating

[

Confirm one of the two displays.

[

STOP VIEWING?

RELEASE PARTY?

REM LAST PTY?

Note:

A second call is not signalled on the Bluetooth

headset.

BASIC SERVICE

SWITCHES

SECOND CALL

ACTIVATE

DEACTIVATE

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands