Siemens HiPath 4000 Operating Manual Download Page 69

Page: 69 / 135

Conducting calls – enhanced functions

Step by Step

Activating/deactivating do not disturb

If you prefer not to be disturbed, you can activate the Do

not disturb function. Internal callers will hear the ringing

tone and the announcement "Do Not Disturb"; external

calls will be diverted to the attendant. System Support

can also set up call forwarding destinations for the Do

Not Disturb function, to which you can forward your in-

ternal and external calls.

Prerequisite:

System Support has enabled the Do Not

Disturb function for all extensions.

Call the system menu.

> <

[

Select and confirm the basic service.

> <

[

Select the menu item and confirm.

> <

[

Select the menu item and confirm. The display indi-

cates whether Do Not Disturb is activated or not.

[

Confirm the display if "Do Not Disturb" should be acti-

vated.

[

Confirm the display if "Do Not Disturb" should be deac-

tivated.

BASIC SERVICE

SWITCHES

DO NOT DISTURB

ACTIVATE

DEACTIVATE

Note:

A tone reminds you that Do Not Disturb is activat-

ed when you seize the trunk.

The attendant can circumvent the Do Not Disturb

function and reach you anyway.

If System Support has locked the Do Not Disturb

function for all users, the item "Do Not Disturb"

will not appear on the service menu.

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands