Siemens HiPath 4000 Operating Manual Download Page 72

Page: 72 / 135

Step by Step

Conducting calls – enhanced functions

Fixed call forwarding

If you have programmed a forwarding destination for

fixed forwarding, you can activate and deactivate the

forwarding facility in the service menu. The pro-

grammed forwarding destination remains valid until you

change or delete it.

Programming and activating a forwarding destina-

tion

Call the system menu.

> <

[

Select and confirm the basic service.

> <

[

Select the menu item and confirm.

[

Confirm. "VARY FORWARD" is displayed.

[

Confirm. "FIXED FORWARD" is displayed. If forwarding

has been programmed, the destination is displayed.

> <

[

Select and confirm.

Enter the phone number for the forwarding destination.

Any destination previously saved will be overwritten.

[

Confirm when the complete number has been entered.

Call forwarding to the programmed destination is active.

Activating and deactivating fixed forwarding

You can only activate and deactivate fixed forwarding if

a destination number has been programmed.

Call the system menu.

> <

[

Select and confirm the basic service.

> <

[

Select the menu item and confirm.

[

Confirm. "VARY FORWARD" is displayed.

[

Confirm.

BASIC SERVICE

DESTINATIONS

FORWARD

ENTER DESTIN.:

SAVE

BASIC SERVICE

DESTINATIONS

FORWARD

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands