Siemens HiPath 4000 Operating Manual Download Page 109

Page: 109 / 135

Additional functions

PC interface (V24, USB)

You can use the PC interface (via a Slim Lumberg cable) to read and modify

phonebook entries, pictures and sounds.

Configuring the PC interface

To configure the PC interface, you must:

1. deactivate the Bluetooth interface on the handset (

Page 102).

2. use a Siemens data cable (

Page 112) to connect the headset/PC in-

terface jack on the handset to the computer.

3. install the MPM application.

For more information, consult your system administrator.

Data transfer mode

Large volumes of data are transferred between the handset and the com-

puter for certain functions. In this case, the handset is switched to data

transfer mode and data transfer appears on the display. In this mode, no

inputs are possible via the keyboard and calls are ignored.

The handset is switched to data transfer mode by:

• activating read/write access to the phonebook

• loading screensavers

• loading melodies

Note:

If the PC interface does not work, first deactivate the Bluetooth in-

terface (

Page 102), then switch the handset off and back on.

Note:

The handset automatically switches to idle if a fault occurs in the

course of transferring data.

Summary of Contents for HiPath 4000








































































































































Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands

Siemens HiPath 4000, Operating Manual

Search results

Summary of Contents for HiPath 4000

Reviews:

Related manuals for HiPath 4000

Brands by name

Popular brands