Shinko PCA1 Instruction Manual Download

Page: 110 / 180

- 110 -

8.2.2 Finishing Fixed Value Control

There are 2 ways to finish Fixed value control:

Using the

key, or using External operation input

• Using the

key

Press the

key for approximately 1 second during Fixed value control.

Fixed value control will stop, and the unit will revert to Program control Stop (in Standby).

• Using External operation input

Close terminals

(STOP) and

(COM) of External operation input.

Fixed value control will stop, and the unit will revert to Program control Stop (in Standby).

(Fig. 8.2.2-1)

Fixed value control RUN

Fixed value control is finished.

Within 0.1 sec

0.1 sec min.

(STOP) and

(COM)

Closed (ON)

(STOP) and

(COM)

Open (OFF)

Controller action

Fixed value control is finished by detecting signal edge action
from OFF to ON of terminals

(STOP) and

(COM).

Summary of Contents for PCA1





















































































































































































Search results

Summary of Contents for PCA1

Reviews:

Related manuals for PCA1

Brands by name

Popular brands

Shinko PCA1, Instruction Manual

Search results

Summary of Contents for PCA1

Reviews:

Related manuals for PCA1

Brands by name

Popular brands