Shinko PCA1 Instruction Manual Download

Page: 93 / 180

- 93 -

Character,

Factory Default

Setting Item, Function, Setting Range

PV color range

• Sets PV color range depending on the user setting.
• Setting range:

Thermocouple, RTD input: 0.1 to 200.0

( )

DC voltage, current input: 1 to 2000

(The placement of the decimal point follows

the selection.)

Available when

(PV color changes continuously) or

[PV color

changes contin Any alarm (EV1 to EV4) is ON: Red] is selected in [PV color].

Backlight time

• Sets time to backlight.

Sets backlight time from no operation status until backlight is switched off.

When set to 0, the backlight remains ON.
Backlight relights by pressing any key while backlight is OFF.

• Setting range:

0 to 99 minutes

At this stage, settings of Other parameters setting group are complete.
If the

and

keys are pressed at the same time, the unit returns to the Engineering setting

group.
By pressing the

key, the unit returns to RUN mode.

Summary of Contents for PCA1





















































































































































































Search results

Summary of Contents for PCA1

Reviews:

Related manuals for PCA1

Brands by name

Popular brands

Shinko PCA1, Instruction Manual

Search results

Summary of Contents for PCA1

Reviews:

Related manuals for PCA1

Brands by name

Popular brands