manualshive.com logo in svg

Shinko PCA1, Instruction Manual

Share
Download
Shinko PCA1 Instruction Manual Download Page 10

- 10 -

Action Indicators, Display

No.

Name

Description

①

PV indicator

Backlight: Red/Green/Orange
Lit when PV is indicated in RUN mode.

②

PV Display

Backlight: Red/Green/Orange
Indicates PV in RUN mode.
Indicates setting characters in setting mode.

③

SV indicator

Backlight: Green
Lit when SV is indicated on the SV/MV/TIME Display.
Retains indicator status at power OFF.

MV indicator

Backlight: Green
Lit when OUT1 MV is indicated on the SV/MV/TIME Display.
Flashes when OUT2 MV is indicated on the SV/MV/TIME Display.
Retains indicator status at power OFF.

TIME indicator

Backlight: Green
Lit when TIME is indicated on the SV/MV/TIME Display.
Retains indicator status at power OFF.

④

SV/MV/TIME
Display

Backlight: Green
Indicates SV, MV or TIME in RUN mode.
Retains display indication at power OFF.
Indicates the set values in setting mode.

⑤

PTN indicator

Backlight: Orange
Lit when the pattern number is indicated.

⑥

PTN Display

Backlight: Orange
Indicates the pattern number.
If ‘Holding’ is selected in [Step SV Hold function when program ends],
flashes when program control ends.

⑦

PROFILE indicator

Backlight: Green
When program control is performing, the indicator lights up depending on
the program setting as follows.

:

Lit when step SV is rising.

:

Lit when step SV is constant.

:

Lit when step SV is falling.

⑧

STEP indicator

Backlight: Orange
Lit when the step number is indicated.

⑨

STEP Display

Backlight: Orange
Indicates the step number.
The step number flashes during Wait action.
Indicates

during Manual control.

⑩

Time unit indicator

Backlight: Green
When the SV/MV/TIME Display indicates TIME, the following is shown
depending on the selection in [Step time unit].
M: Lit when ‘Hours:Minutes’ is selected in [Step time unit].
S: Lit when ‘Minutes:Seconds’ is selected in [Step time unit].

Summary of Contents for PCA1





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands