Shinko PCA1 Instruction Manual Download | Manualshive

Page: 67 / 180

background image

- 67 -

Character,

Factory Default

Setting Item, Function, Setting Range

: Pt100 -148.0 to 212.0
: Pt100 -148.0 to 932.0
: 4 to 20 mA DC -2000 to 10000
: 0 to 20 mA DC -2000 to 10000
: 0 to 10 mV DC -2000 to 10000
: -10 to 10 mV DC -2000 to 10000
: 0 to 50 mV DC -2000 to 10000
: 0 to 100 mV DC -2000 to 10000
: 0 to 1 V DC -2000 to 10000
: 0 to 5 V DC -2000 to 10000
: 1 to 5 V DC -2000 to 10000
: 0 to 10 V DC -2000 to 10000

Scaling high limit

• Sets scaling high limit value.
• Setting range:

Scaling low limit value to Input range high limit value

Scaling low limit

• Sets scaling low limit value.
• Setting range:

Input range low limit value to Scaling high limit value

Decimal point place

• Selects decimal point place.
• Selection item:

: No decimal point
: 1 digit after decimal point
: 2 digits after decimal point
: 3 digits after decimal point
: 4 digits after decimal point

Available for DC voltage and current inputs.

Sensor correction

• Sets sensor correction value.

[Sensor correction function]

When a sensor cannot be set at the exact location where control is desired, the
sensor-measured temperature may deviate from the temperature in the
controlled location. When using multiple indicating controllers, sometimes the
measured temperatures do not concur due to differences in sensor accuracy or
dispersion of load capacities. In such a case, the control can be set at the desired
temperature by adjusting the input value of sensors. However, it is effective
within the input rated range regardless of the sensor correction value.

PV after sensor correction= Current PV + (Sensor correction value)

• Setting range:

Thermocouple, RTD input: -200.0 to 200.0

( )

DC voltage, current input: -2000 to 2000

(The placement of the decimal point

follows the selection.)

«
...
65
66
67
68
69
...
»

Summary of Contents for PCA1





















































































































































































Reviews:

No comments

Related manuals for PCA1

7000-2 - Escalade RAID Controller

Brand: 3Ware Pages: 2

Origami 4M-006-01

Brand: 4 Moms Pages: 28

Brand: Magellan Pages: 2

Brand: NCR Pages: 8

Brand: DSE Pages: 2

Brand: Daruifuno Pages: 24

Brand: TeleMann Pages: 4

Brand: Monster Central Pages: 13

Brand: Rain Bird Pages: 18

fantech ECO-FEEL 414729

Brand: SystemAir Pages: 2

Brand: BG Systems Pages: 24

Brand: Daspi Pages: 16

Brand: Daikin Pages: 16

SmartMonitor MMU2-16LE Series

Brand: EDI Pages: 62

Brand: Navilock Pages: 14

ISC.ANT.U500/270DM-E

Brand: Feig Electronic Pages: 117

Brand: Oriental motor Pages: 52

Brand: Opt Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands