manualshive.com logo in svg

Shinko PCA1, Instruction Manual

Share
Download
Shinko PCA1 Instruction Manual Download Page 62

- 62 -

7.4 AT Perform Group

In AT Perform group, the following can be set:

AT mode, AT Perform/Cancel, AT bias

•

To enter AT Perform group

Press the

key once in RUN mode, and press the

key 3 times. The PV Display indicates

,, and the unit enters the AT Perform group.

Press the

in the AT Perform group. The PV Display indicates

, and the unit enters ‘AT

mode’.

•

Explanation of Setting Item

Upper left: PTN Display, PV Display

The PTN Display is unlit, and the PV Display indicates setting item characters.

Lower left: STEP Display, SV/MV/TIME Display

The STEP Display is unlit, and the SV/MV/TIME Display indicates factory default.

Right side: Indicates the setting item, explanation of its function, and setting range.

AT mode

• Selects AT mode.
• Selection item:

: Normal mode

Setting items in the AT Perform group are shown below.

Character,

Factory Default

Setting Item, Function, Setting Range

AT mode

• Selects AT mode.

Multi mode is enabled only during program control.

• Selection item:

: Normal mode

When AT Perform is selected in [AT Perform/Cancel], AT starts

immediately.

: Multi mode

AT is automatically performed at the point where 90% of
progressed step time has elapsed.
If there are the same PID block numbers in one pattern, the AT is
performed only for the first step.

AT Perform/Cancel

• Selects AT Perform/Cancel.

AT continues to perform when input errors (overscale, underscale) occur.
AT will be forced to stop if it has not been completed within 4 hours.

• Selection item:

: AT Cancel
: AT Perform

PTN Display

STEP Display

PV Display

SV/MV/TIME Display

Setting item, function, setting range (or selection item)

Summary of Contents for PCA1





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands