manualshive.com logo in svg

Shinko PCA1, Instruction Manual

Share
Download
Shinko PCA1 Instruction Manual Download Page 69

- 69 -

7.5.2 Output Parameter Setting Group

In Output parameter setting group, the following can be set:

OUT1 proportional cycle, OUT1 ON/OFF hysteresis, OUT2 proportional cycle (DR, DS or DA
option), OUT2 cooling method (DR, DS or DA option), Direct/Reverse action, etc.

Setting items in the Output parameter setting group are shown below.

Character,

Factory Default

Setting Item, Function, Setting Range

• Relay contact

output: 30 sec

• Non-contact

voltage output:

3 sec

OUT1 proportional cycle

• Sets OUT1 proportional cycle.
• Setting range:

1 to 120 sec

Available when control output OUT1 is Relay contact output or Non-contact voltage
output.

OUT1 ON/OFF hysteresis

• Sets OUT1 ON/OFF hysteresis.

(Fig. 7.5.2-1)

• Setting range:

Thermocouple, RTD input: 0.1 to 1000.0

( )

DC voltage, current input: 1 to 10000

(The placement of the decimal point follows

the selection.)

•

DR: 30 sec

•

DS: 3 sec

OUT2 proportional cycle

• Sets OUT2 proportional cycle.
• Setting range:

1 to 120 sec

Available when Heating/Cooling control (DR or DS option) is ordered.

OUT2 cooling method

• Selects OUT2 cooling method.

(Fig. 7.5.2-2)

ON

OFF

SV

OUT1

hysteresis

Hysteresis

OUT2 proportional band

SV

Air cooling

Oil cooling
Water cooling

Summary of Contents for PCA1





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands