Shinko PCA1 Instruction Manual Download | Manualshive

Page: 74 / 180

background image

- 74 -

Setting items in the Event output parameter setting group are shown below.

Character,

Factory Default

Setting Item, Function, Setting Range

Event output EV1 allocation

• Selects Event output EV1 from the Event Output Allocation Table below.

For Alarm output, the alarm value is set by

deviation from the SV

(excluding Process alarm), and if the input goes outside the range, the
Alarm output is turned ON (turned OFF for High/Low limit range alarm).
When De-energized action is selected, the output is activated conversely.
Pattern end output turns ON after program control ends.
Loop break alarm output turns ON after detecting actuator trouble (heater
burnout, heater adhesion) or sensor burnout.
‘Output during AT’ turns ON during AT.

• Selection item:

[Event Output Allocation Table]

Selection

Event output

Remarks

No event
Alarm output, High limit alarm
Alarm output, High limit with standby alarm
Alarm output, Low limit alarm
Alarm output, Low limit with standby alarm
Alarm output, High/Low limits alarm
Alarm output, High/Low limits with standby
alarm
Alarm output, High/Low limit range alarm
Alarm output, High/Low limit range with
standby alarm
Alarm output, Process high alarm
Alarm output, Process high with standby
alarm
Alarm output, Process low alarm
Alarm output, Process low with standby
alarm
Pattern end output
Loop break alarm output
Output during AT

Turns ON during AT.

When

001 to 012 (Alarm output) is selected, one alarm can be set to one event output.

When 013 to 015 is selected, each output is common to multiple event outputs.

EV1 alarm hysteresis

• Sets EV1 alarm hysteresis.
• Setting range:

Thermocouple, RTD input: 0.1 to 1000.0

( )

DC voltage, current input: 1 to 10000

(The placement of the decimal point

follows the selection.)

Available when 001 to 012 (Alarm output) is selected in [Event output EV1 allocation].

EV1 alarm delay time

• Sets EV1 alarm action delay time.

When setting time has elapsed after PV enters the alarm output range, the
alarm is activated.

• Setting range:

0 to 10000 seconds

Available when 001 to 012 (Alarm output) is selected in [Event output EV1 allocation].

«
...
72
73
74
75
76
...
»

Summary of Contents for PCA1





















































































































































































Reviews:

No comments

Related manuals for PCA1

Brand: ABB Pages: 370

Brand: ABB Pages: 17

Brand: ABB Pages: 104

Brand: ABB Pages: 120

Brand: ABB Pages: 42

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 10

Brand: Febco Pages: 12

Brand: GameSir Pages: 8

Brand: Game ready Pages: 21

Brand: VAMP Pages: 304

Brand: Tactical Pages: 8

Brand: Uniden Pages: 28

Brand: UniFocus Pages: 23

Brand: UniFocus Pages: 6

Brand: SYR Pages: 2

AMES 4000SS Series

Brand: Watts Pages: 8

Brand: Anilam Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands