manualshive.com logo in svg

Shinko PCA1, Instruction Manual

Share
Download
Shinko PCA1 Instruction Manual Download Page 47

- 47 -

7.2 Block Setting Group

In the Block setting group, the following setting groups are included:

PID block setting group, Time signal block setting group, Wait block setting group, Alarm block setting
group, Output block setting group

About settings in each block setting group

If program pattern is not set for a step, its block number becomes 0 (zero). We highly recommend that
you leave the factory default of Block 0 in each block setting group as they are, and set the values
from Block 1.

•

To enter the Block setting group

Press the

in RUN mode, and press

key (in that order). The PV Display indicates

,

and the unit enters the Block setting group in Group selection mode.
Press the

in the Block setting group. The PV Display indicates

, and the unit enters PID

block setting group.
Every time the

key is pressed, the block setting groups are switched as shown below.

By pressing the

key at each block setting group, the unit moves to the setting items in the group.

(*1) Available when Time signal output (TS option) is ordered.
(*2) Available when 001 to 012 (Alarm output) is selected in [Event output EV

allocation].

•

Explanation of Setting Item

Upper left: PTN Display, PV Display

The PTN Display is unlit, and the PV Display indicates setting item characters.

Lower left: STEP Display, SV/MV/TIME Display

The STEP Display is unlit, and the SV/MV/TIME Display indicates factory default.

Right side: Indicates the setting item, explanation of its function, and setting range (or selection item).

Block 0 OUT1 proportional band

• Sets Block 0 OUT1 proportional band.
• Setting range:

Thermocouple, RTD input without decimal point: 0 to input span

( )

PID block setting group

Time signal block setting group

(*1)

Wait block setting group

Alarm block setting group

(*2)

Output block setting group

Setting items in the group

Setting items in the group

Setting items in the group

Setting items in the group

Setting items in the group

PTN Display

STEP Display

PV Display

SV/MV/TIME Display

Setting item, function, setting range (or selection item)

Summary of Contents for PCA1





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands