MX-2300/2700 N/G SIMULATION 7 – 106
51
51-1
Purpose
: Adjustment
Function (Purpose)
: Used to adjust the ON/OFF timing of the
transfer voltage and the separation bias
voltage.
Section
: Process
Item
: Operation (Transfer)
Operation/Procedure
1)
Select the set item with [
↑
] and [
↓
] buttons.
The highlighted section of the set value is switched and dis-
played on the set setting area.
* If there is any item over [
↑
], an active display is made and
item is shifted.
If there is no item over [
↑
], the display grays out and the
operation is invalid.
If there is any item under [
↓
], an active display is made and
item is shifted.
If there is no item over [
↓
], the display grays out and the
operation is invalid.
2)
Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3)
When [OK], [
↑
], [
↓
] button, [COLOR], or [BLACK] key is
pressed, the current set value is saved to EEPROM and RAM.
<Set range and default value of each set value>
When the value of transfer ON/OFF timing is decreased, the trans-
fer ON/Off timing for paper is advanced.
When the value of transfer ON/OFF timing is increased, the trans-
fer ON/Off timing for paper is delayed.
(
±
1: about 10ms change)(Set range: –490 to +490ms)
51-2
Purpose
: Adjustment
Function (Purpose)
: Used to adjust the contact pressure of
paper against the registration roller (main
unit paper feed section, duplex paper feed,
SPF paper feed) on each section. (When
there are much variations in print image
positions for paper or when the paper jam
occurs, the adjustment is required.) Used to
change the deflection quantity correction
value of each specified cassette.
Section
: Paper transport
Item
: Operation
Operation/Procedure
1)
Select a category to be set. (In this example, [SIDE1] is
selected.)
* Select a category, and the selected button is highlighted.
The set item of the selected category button is displayed.
* Only one button can be selected. The selected button is
highlighted.
On the initial display, [SIDE1] is selected.
Select the set item with [
↑
] and [
↓
] buttons.
The highlighted section of the set value is switched and dis-
played on the set setting area.
* If there is any item over [
↑
], an active display is made and
item is shifted.
If there is no item over [
↑
], the display grays out and the
operation is invalid.
If there is any item under [
↓
], an active display is made and
item is shifted.
BK-MAG
ADJ (BK-MAG)/PAPER/
COUNT
BK-MAG adjustment value,
correction value
ADJ: 1 to 199 (–199 to +199)
ADJ STEP
PAPER: -
COUNT: Times
PAPER_SCAN DEVICE: OC, SPF1, SPF2
PAPER_PAPER_SIZE: A4, A4R, A3, LT,
LTR, WL PAPER_CS: MFT,CS1,CS2, CS3,
CS4,LCC PAPER_PRINT_DIR: F, R, U, L
COUNT: 0 to 255
BK-MAG
BK-MAG data
-9.99 to +9.99
mm
SCAN_MAG (SUB, MAIN)
BK-MAG scan magnification ratio
correction value
SUB:-99 to +99
MAIN:-4.99 to +4.99
SUB:MAIN:-4.99
to +4.99
ERROR
Error history
–
Error code
ADJ_MFT (LEAD/OFST)
PRINT adjustment value,
correction value
LEAD,OFST:-4.9 to +4.9 PAPER_SCAN
DEVICE: LEAD, OFST: OC, SPF1, SPF2
PAPER_PAPER_SIZE: A4, A4R, A3, LT,
LTR, WL
PAPER_PRINT_DIR: F, R, U, L COUNT: 0
to 255
LEAD, OFST:
mm
PAPER:
–
COUNT:
Times
LEAD (F/C/R)
PRINT lead edge data
-4.9 to +4.9
mm
OFFSET R (U/M/L)/F (U/M/L)
Off-center data
-4.9 to +4.9
mm
ERROR
Error history
–
Error code
Adjustment item
(page)
Item display
Display content
Display range (difference from the
previous value)
Unit
Item
Display item
Description of
content
Set
range
Default
value
A
TC2 ON TIMING
Secondary transfer
voltage ON timing
setting
1 to 99
40
B
TC2 OFF TIMING
Secondary transfer
voltage OFF timing
setting
1 to 99
60
0
SIMULATION
NO.50
̆
28
TEST
AUTO
IMAGE
POSITION
ADJUSTMENT
㧦
SERVICE
CLOSE
ADJ_OC
(SCAN / LEAD / OFST)
㧦
50(
r
99) / 50(
r
99) / 50(
r
99)
SCAN(F /C /R) / LEAD(F /C /R)
㧦r
4.99 /
r
4.99 /
r
4.99 ,
r
4.9 /
r
4.9 /
r
4.9
OFFSET
DATA_
R(U /M /L) / F(U /M /L)
㧦r
4.9 /
r
4.9 /
r
4.9 ,
r
4.9 /
r
4.9 /
r
4.9
SCAN_MAIN
㧦r
4.99
BK-MAG
OC
SPF
OK
0
A:
A
㧦
40
B
㧦
60
㧧
TC2 ON TIMING
㧧
TC2 OFF TIMING
SIMULATION
NO.51
㧙
01
TRANSCRIPTION TIMING SETUP
40
㨇
1
㨪
99
㨉
TEST
CLOSE
OK