manualshive.com logo in svg

Sharp AJ-6020, Operation Manual, Page: 72 / 93

Share
Download
Sharp AJ-6020 Operation Manual Download Page 72

70

USING THE PRINTER MODE

The unit can be used as a printer after installing the printer driver onto your computer. Refer
to "Print" in the Online Manual for information on using the unit as a printer. Load paper into
the unit for printing in the same way as for copying.

RESERVING COPY AND SCAN JOBS

Reserving a copy job

While the unit is printing, make copy settings, and press the "START" button (

) to

reserve the job. After printing is completed, copying will start. The messages will change as
below.

Reserving a scan job

While the unit is printing, make the scan setting using the "SCAN" button, and press the
"START" button (

) to reserve the job, after printing is completed, scanning will start.

You cannot send a copy or scan job while printing from the bypass tray.

Printing...
Ready to program

Make the  copy settings and press the START button 
(       ) to reserve the job.

Printing...
Waiting to Copy

After printing is completed, copying will start.

Printing...
Ready to program

Make the scan settings, and press the START button 
(       ) to reserve the job.

Printing...
Waiting to Scan

After printing is completed, scanning will start.

Summary of Contents for AJ-6020






























































































Reviews:

No comments