manualshive.com logo in svg

Sharp AJ-6020, Operation Manual, Page: 13 / 93

Share
Download
Sharp AJ-6020 Operation Manual Download Page 13

11

CONNECTING THE INTERFACE CABLE

This unit includes both USB and parallel interface connectors.
Interface cables for connecting the unit to your computer are not included with this unit.
Please purchase the appropriate cable for your computer.

Connecting the parallel interface cable

1

Obtain an IEEE1284 shielded parallel interface cable.

2

Ensure that your computer and unit are turned off.

3

Insert the cable into the parallel interface connector located on
the rear of the unit, and fasten with clasps.

4

Insert the other end of the cable into the interface connector of
your computer.

Connecting the USB interface cable

1

Obtain a shielded USB interface cable.

2

Insert the cable into the USB interface connector located on the
rear of the unit.

3

Insert the other end of the cable into the interface connector of
your computer, or the USB hub connected to your computer.

Do not connect both the USB interface cable and the parallel interface cable to this
unit at the same time.

USB is available with a PC/AT compatible computer that was originally equipped
with USB and had Windows 98, Windows Me or Windows 2000 preinstalled.

Summary of Contents for AJ-6020






























































































Reviews:

No comments