manualshive.com logo in svg

Sharp AJ-6020, Operation Manual, Page: 18 / 93

Share
Download
Sharp AJ-6020 Operation Manual Download Page 18

16

INSTALLING THE PRINT HEADS AND THE INK TANKS

12

Close the maintenance cover.

13

Close the front cover.

Press both edges of the front cover with both of your hands until it locks.

14

The unit will automatically start a sequence to clean the print
heads and the following message will appear.

15

After the cleaning sequence is complete, the machine will
automatically print the alignment patterns while the following
message appears.

16

Align the print heads following the procedure "ALIGNING THE
PRINT HEAD". Since the patterns have been already printed,
start with step 5 on page 18.

To ensure that the ink heads do not become dry, always leave the ink tanks
installed. If not, poor output will result.

During ink tank replacement, if the cover is left open for more than 8 minutes, the
carriage will automatically return to its home position.

Cleaning the Print
Head...

Printing...
Alignment Patterns

Summary of Contents for AJ-6020






























































































Reviews:

No comments