Sanyo Denki SANMOTION 3E S Instruction Manual Download Page 37

Page: 37 / 488

1.3 Illustration Of System Components

1-14

Preface

SANMOTION R 3E Model

RS3D80#

Motor encoder

SANMOTION R 3E Model

RS3PAC550

R S T

36 pin cable for power unit/amplifier connection

Servo motor

■

Power unit: RS3PAC550, Amplifier unit: RS3D80

Switches power
On/Off.
Be sure to construct
safety circuit for safe.

Noise filter

Electromagnet
ic contactor

Wiring breaker

(MCCB)

Installed to
protect power
line from external
noise.

Used to protect
power line.
Turns off the power
supply when
overload runs.

Control Power

DC24V

Power ground

Be sure to grounding.

Power ground

Be sure to grounding.

DC power
wiring (+/-)

Refer the section
4.5.5 for wiring of
dynamic brake
signal and external
regenerative
resistor thermostat.

TH1-1

TH1-2

：

Terminal for thermal signal

DB1, DB2

：

Output for dynamic

brake contact

External regenerative
resistor

Motor power (System-1)

Motor power (System-2)

Host equipment

To next amplifier

General I/O connector
Connects homing,
probing and general
signals.

Enables parameter setup
and monitoring through
communication with a PC.

Motor Setup
Software

USB

Summary of Contents for SANMOTION 3E S









































































































































































































































































































































































































































































































Search results

Summary of Contents for SANMOTION 3E S

Reviews:

Sanyo Denki SANMOTION 3E S, Instruction Manual, Page: 37 / 488

Search results

Summary of Contents for SANMOTION 3E S

Reviews: