Home
/
Sanyo Denki
/
SANMOTION 3E S
/
Instruction Manual

Sanyo Denki SANMOTION 3E S, Instruction Manual, Page: 138 / 488

Share

Page: 138 / 488

Sanyo Denki SANMOTION 3E S Instruction Manual Download Page 138

4. Wiring

4-1

4.1 Wiring for the terminal of high voltage and grounding

4.1.1 Part name and function

■

Input voltage 200V AC

Terminal name

Connector

marking

Remarks

Main circuit power supply

R

･

T

or

R

・

S

・

T

Single phase 100 to 120 VAC +10%, -15% 50/60Hz±3%
Single phase 200 to 240 VAC +10%, -15% 50/60Hz±3%

Three-phase

200 to 240 VAC +10%, -15% 50/60Hz±3%

Control power supply

r

・

t

Single phase 100 to 120 VAC +10%, -15% 50/60Hz±3%
Single phase 200 to 240 VAC +10%, -15% 50/60Hz±3%

Servo motor connector

U

・

V

・

W

Connected with servo motor

Protective grounding

terminal

Connected with grounding wire of power supply and of servo
motor.

Regeneration resistance

connector

RB1

・

RB2

RB4

RS3

□

01

RS3

□

02

RS3

□

03

RS3A05
RS3A30
RS3W60

Connects regenerative resistance to terminal
RB1 and RB2. Built-in regenerative resistor
model has already connected at factory
setting.
Connects external regenerative resistor to
terminal RB1 and RB2 when regenerative
performance is insufficient.
RB4 terminal is not equipped.

RS3A07
RS3A10
RS3A15

Built-in regenerative resistor model has
short-bar between RB1 and RB4 at factory
setting.
Connects external regenerative resistor to
terminal RB1 and RB2 after removing the
short-bar when regenerative performance is
insufficient.

Maker maintenance

P

・

For maker maintenance. Do not connect anything.

«
...
136
137
138
139
140
...
»

Summary of Contents for SANMOTION 3E S









































































































































































































































































































































































































































































































Reviews:

No comments