manualshive.com logo in svg

Sanyo Denki SANMOTION 3E S, Instruction Manual, Page: 197 / 488

Share
Download
Sanyo Denki SANMOTION 3E S Instruction Manual Download Page 197

 

5.4 Test operation 

 

 

5-14

  

 

 

5

 

Linear motor

 

 

 

 

 

 

 

 

 

5.2.4 Check of operation 

 

[Step 1: JOG operation] 

■

 

Run the JOG operation without a load on the stage. 

 

■

 

Check whether the linear motor is able to move to positive and negative direction full stroke. 

 
 
 
 
 
 
 
 
 

*  The forward direction means the direction where motor power line lead pulled out. 
*  Please perform operation with safety speed. 

 
 

  How to operate through the setup software 

Select JOG operation at the menu of Test Operation. See the manual: M0010842, "7.1 
JOG operation" for detail of the setup software operation.     

 

  How to operate through the digital operator 

See "7.6.1 Velocity-controlled JOG Operation" for detail of the digital operator 
operation. 

 

 

←

 

Reverse direction

 

Forward direction 

→

 

Move motor beyond 2 magnets or more. 

Summary of Contents for SANMOTION 3E S









































































































































































































































































































































































































































































































Reviews:

No comments