Samsung SHR-4080P User Manual Download Page 20 | Manualshive

Page: 20 / 171

background image

SHR-4080P USER’S MANUAL

2-7

8. Check the connector, wiring, and cable fixing condition inside the product and close

the cover.

9. Tighten cover-fixing screws. (5 points on both sides and 1 point in the back side)

✻

You can apply 2 HDDs to each BRACKET-HDD as shown in the figure.

Attention

Attention

For HDD addition, please select the same HDD with the existing HDD fixed to the
product as far as possible. This product can accept 4 more HDDs, 2 at Primary Slot
and 2 at Secondary Slot respectively. Both HDDs attached to Primary Slot and
Secondary Slot shall be set to Master and Slave respectively. Refer to User’s Manual
for Master or Slave Jumper Setting.
In the event of only one HDD installation, it shall be inserted into the Primary slot.

Note

Note

Refer to Appendix 2 to see which HDD specifications are supplied.

«
...
18
19
20
21
22
...
»

Summary of Contents for SHR-4080P












































































































































































Reviews:

No comments

Related manuals for SHR-4080P

Brand: SAFE-TECH Pages: 426

Brand: Q-See Pages: 7

Brand: Guardian Pages: 47

Brand: Argus Pages: 65

MPEG4 Recorder 1

Brand: Neuros Pages: 2

Brand: Gadspot Pages: 77

Brand: GE Interlogix Pages: 48

Brand: Encore Pages: 2

Brand: 360 Vision Pages: 88

Brand: Eyemax Pages: 71

Brand: Security Labs Pages: 24

Brand: HAI Pages: 7

Brand: Piezel Pages: 2

Brand: Handy-View Pages: 71

P2P HD720P BULB

Brand: EazzyDV Pages: 25

WJRT416 - 16CH DIGITAL RECORDER

Brand: Panasonic Pages: 88

Brand: Grundig Pages: 32

Brand: Grundig Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands