•
Rx level (or RSL) at both ends must not differ significantly from the
previously calculated value.
•
Modulation indicates which modulation mode is used. For better operation
the same modulation must be set at both ends.
•
Radial MSE is explained below in the Chapter 3.1.1.
•
LDPC is explained below in the Chapter 3.1.2.
6.
ODU data status
– shows if management CPU was able to read data from radio;
7.
ODU side
– shows the radio side of local and remote CFIP (command line –
radio
side
);
8.
Tx mute
– shows if transmitter is currently muted;
9.
Tx power
– shows current transmitter power in dBm. Factory default setting is “Off”
(command line -
radio status
or
status
);
10.
ATPC
– shows if ATPC is enabled or disabled (command line –
atpc status
);
11.
Rx level
– shows current level of received signal. It must not differ significantly from
the previously calculated value (command line -
radio status
or
status
);
12.
Duplex shift
– shows the margin between the transmitting and receiving frequencies
(command line -
radio status
);
13.
Tx frequency
– shows the transmitting frequency (command line -
radio status
);
14.
Rx frequency
– shows the receiving frequency (command line -
radio status
);
15.
Configuration file
– shows which configuration the modem is currently using. It
should match on both sides of the link (command line –
modem configuration
);
16.
Bandwidth
– shows width of currently utilized bandwidth in MHz (command line –
modem status
or
status
);
17.
Modulation
– shows modulation mode set (command line –
modem status
or
status
);
18.
Total capacity
– shows total capacity set (command line –
modem status
);
19.
Ethernet capacity / rate
– shows Ethernet capacity set and rate limitation of
Ethernet switch. If Ethernet rate is not limited “Unlimited” will be displayed after
“/” symbol (command line –
modem status
or
status
);
20.
E1 channels
– shows number of E1 channels set. The number must be equal at both
ends (command line –
modem status
or
status
);
21.
IDU data status
– shows if management CPU was able to read data from modem;
22.
IDU status
– indicates the acquire status of the modem. ‘ACQUIRE_IN_PROGRESS’
will appear during start-up, when modem acquires required parameters, but in
normal operation mode ‘ACQUIRE_LOCKED’ will be seen. Any other options
designate failure (command line –
modem status
or
status
);
23.
Radial MSE
– shows radial mean square error value. Refer to Chapter 3.1.1
.
for
detailed description (command line -
modem status
or
status
);
24.
LDPC decoder stress
– shows the load of LDPC (low-density parity-check code)
decoder. Refer to Chapter 3.1.2
.
for detailed description (command line –
modem
status
or
status
);
25.
ACM engine
– shows if ACM (Adaptive Coding and Modulation) engine is enabled
(command line –
modem status
or
status
);
26.
Current modulation Rx / Tx
– shows the modulation modes currently utilized
(command line –
modem status
);
27.
Current link capacity Rx / Tx
– shows the current capacities in both directions
(command line –
modem status
);
28.
E1 status
– shows if the E1 channel is connected or not and shows status of LOS and
AIS indications. To see the status, click on the text (command line –
e1 status
);
29.
Diagnostics data status
– shows if system parameters are in acceptable margins
(command line -
diagnostics
);
CFIP PhoeniX Series TDM/IP Split Mount System Technical Description and Configuration Guide
•
Rev. 1.13
•
© SAF Tehnika JSC 2015
35