RKC INSTRUMENT DeviceNet COM-JH Instruction Manual Download Page 20

Page: 20 / 116

4. WIRING

IMR01Y09-E3

•

Termination resistors:
Install termination resistors to both ends of a trunk line in DeviceNet.
Specification of termination resistor: 121

Ω

1 %, 1/4 W (Metal film resistance)

•

Communications power supplies:
To use DeviceNet, connect a communications power supply (24 V DC) to the communications

connector of each node with a cable.

•

Communication length:

Maximum network length *

Communication

speed

Thick trunk length Thin trunk length

Maximum

drop length

Cumulative

drop length

125 kbps

500 m

156 m or less

250 kbps

250 m

100 m

6 m

78 m or less

500 kbps

100 m

39 m or less

* Maximum distance between nodes

For details of DeviceNet Network installation conditions and methods, refer to the
instruction manual of the DeviceNet master unit or DeviceNet Specifications.
DeviceNet specifications are available at ODVA (Open DeviceNet Vendor Association).

URL: http://www.odva.org

Summary of Contents for DeviceNet COM-JH





















































































































Search results

Summary of Contents for DeviceNet COM-JH

Reviews:

Related manuals for DeviceNet COM-JH

Brands by name

Popular brands

RKC INSTRUMENT DeviceNet COM-JH, Instruction Manual

Search results

Summary of Contents for DeviceNet COM-JH

Reviews:

Related manuals for DeviceNet COM-JH

Brands by name

Popular brands