RKC INSTRUMENT DeviceNet COM-JH Instruction Manual Download Page 12

Page: 12 / 116

2. HANDLING PROCEDURES

IMR01Y09-E3

Controller setting

DeviceNet

communication setting

Programming

Set communication parameters of controller.

•

See

8.3 Setting of Use Instruments (P. 77)

•

See

FB400/FB900 Communication Quick Manual

(IMR01W07-E )

Set COM-JH communication parameters relating to polling I/O
communication by using the DeviceNet configuration tool.

See

6.2.1 Polling I/O communication (P. 27)

and the Instruction

Manual of Configuration Tool.

Installation of

the EDS file

Install the EDS file of COM-JH in a configuration tool of DeviceNet.
The EDS file is attached to a COM-JH as a floppy disk.

See the Instruction Manual of Configuration Tool.

Data download

Download each device parameter created by the DeviceNet configuration tool
to device on the actual network.

See the Instruction Manual of Configuration Tool.

Create the sequence program.

See

8.4 Sample Programs (P. 78)

PLC setting

Set communication parameters of PLC.

See

8.3 Setting of Use Instruments (P. 77)

and Instruction Manual

for the used PLC.

Summary of Contents for DeviceNet COM-JH





















































































































Search results

Summary of Contents for DeviceNet COM-JH

Reviews:

Related manuals for DeviceNet COM-JH

Brands by name

Popular brands

RKC INSTRUMENT DeviceNet COM-JH, Instruction Manual

Search results

Summary of Contents for DeviceNet COM-JH

Reviews:

Related manuals for DeviceNet COM-JH

Brands by name

Popular brands