Ricoh LP131n Operating Instructions Manual Download Page 96

Page: 96 / 204

Press the [Menu] key.

AUB051S

The [Menu] screen appears.

Press the [ ] or [ ] key to display [Paper Input], and then press the [ Enter] key.

Press the [ ] or [ ] key to display [Paper Type], and then press the [ Enter] key.

Press the [ ] or [ ] key to select the tray, and then press the [ Enter] key.

Press the [ ] or [ ] key to select the paper type, and then press the [ Enter] key.

Press the [Online] key.

The initial screen appears.

• The following paper types cannot be printed on both sides:

• Special Paper, Color Paper, Preprinted, Thick Paper

Loading Paper in the Bypass Tray

• Shuffle the paper before loading the stack onto the tray, so multiple sheets are not fed in together.

5. Paper and Other Media

Summary of Contents for LP131n












































































































































































































Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands

Ricoh LP131n, Operating Instructions Manual

Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands