Ricoh LP131n Operating Instructions Manual Download Page 103

Page: 103 / 204

Load envelopes until they stop, with the print side up and the sides of the flaps on the left as
shown below.

AUB260S

Slide the side guides against the edge of the envelope stack.

Set the envelope size and feed direction. Press the [Menu] key.

AUB051S

The [Menu] screen appears.

Press the [ ] or [ ] key to display [Paper Input], and then press the [ Enter] key.

Check [Bypass Size] appears, and then press the [ Enter] key.

Press the [ ] or [ ] key to select the envelope type, and then press the [ Enter] key.

Press the [Online] key.

The initial screen appears.

• Confirm that the top of the stack is not higher than the limit mark on the side guides.

Loading Paper

101

Summary of Contents for LP131n












































































































































































































Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands

Ricoh LP131n, Operating Instructions Manual

Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands