Ricoh LP131n Operating Instructions Manual Download Page 22

Page: 22 / 204

Interior

AUB055S

1. Memory Unit Type C 128MB/ 256MB (SDRAM module)

Install 128 MB or 256 MB SDRAM module into the controller board slot.
See p.29 "Attaching Memory Unit Type C 128MB/256MB (SDRAM Module)"

2. Optional cards

See p.40 "Attaching Optional Cards".

3. Optional boards

See p.33 "Attaching IEEE 802.11b Interface Unit".
See p.37 "Attaching Gigabit Ethernet Board Type A".

4. Hard Disk Drive Type 2650

See p.27 "Attaching Hard Disk Drive Type 2650".

• You cannot install following options at the same time:

• IEEE 802.11b Interface Unit
• Gigabit Ethernet Board Type A

Caution when re-installing the controller board

This section describes handling the controller board when installing options.
If you slide out the controller board to install units, carefully read the instruction to re-install the controller
board.

2. Installing Options

Summary of Contents for LP131n












































































































































































































Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands

Ricoh LP131n, Operating Instructions Manual

Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands