Ricoh LP131n Operating Instructions Manual Download Page 144

Page: 144 / 204

Confirm the position of the image on the test sheet, and then adjust the registration value.

ZKEX480E

In this setting, adjust the margins of the test sheet so that they are equal in size.

In the [Registration] menu, press the [ ] or [ ] key to select [Adjustment], and then press
the [ Enter] key.

Press the [ ] or [ ] key to select the parameter you want to adjust, and then press the [
Enter] key.

Press the [ ] or [ ] key to set the registration value (mm), and then press the [ Enter] key.

Increase the value to shift the print area in the positive direction, and decrease to shift in the negative
direction.

TS3X001N

8. Adjusting the Printer

142

Summary of Contents for LP131n












































































































































































































Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands

Ricoh LP131n, Operating Instructions Manual

Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands