Ricoh LP131n Operating Instructions Manual Download Page 114

Page: 114 / 204

Replacing the Maintenance Kit

• The inside of this printer becomes very hot. Do not touch parts labeled " " (indicating a hot surface).

Touching these parts will result in burns.

• Grip the plug, not the cord, when pulling the plug from the socket. Pulling the cord causes wear and

tear that can result in fire or electric shock.

• Wait at least one hour after power off before replacing parts. Not allowing the printer to cool may

result in burns.

When to replace the Maintenance Kit.

"Replace Maintenance Kit"
The maintenance kit contains parts for maintaining the printer.
Replace the maintenance kit if the following message appears on the display:

Before Replacing

Replace all the parts included in Maintenance Kit at the same time. Replace them according to the following
procedure.

Turn off the power, and then unplug the power cable.

Check the box contains the following items:

AUB037S

1. Friction Pad × 3

See "Replacing the Friction Pad".

2. Transfer Roller (with gloves)

See "Replacing the Transfer Roller".

6. Replacing Consumables and Maintenance Kit

112

Summary of Contents for LP131n












































































































































































































Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands

Ricoh LP131n, Operating Instructions Manual

Search results

Summary of Contents for LP131n

Reviews:

Related manuals for LP131n

Brands by name

Popular brands