Ricoh AFICIO MP 6001 Troubleshooting Manual Download Page 15

Page: 15 / 160

1. When the Machine Does Not Operate

As Wanted

This chapter describes basic troubleshooting procedures that are applicable to all functions of this machine.

Indicators

This section describes the indicators displayed when the machine requires the user to remove misfed paper,
to add paper, or to perform other procedures.

Indicator

Status

: Misfeed indicator

Appears when a misfeed occurs.
See p.121 "Removing Jammed Paper".

: Load Paper indicator

Appears when paper runs out.
See "Loading Paper", About This Machine

: Add Toner indicator

Appears when toner runs out.
See "Adding Toner", About This Machine

: Add Staple indicator

Appears when staples run out.
See "Adding Staples", About This Machine

: Waste Toner Full indicator

Appears when the waste toner bottle is full.
Contact your sales or service representative.

: Empty Hole Punch Receptacle

indicator

Appears when the hole punch receptacle is full.
See p.141 "Removing Punch Waste".

: Empty Waste Staple Receptacle

indicator

Appears when the waste staple receptacle is full.
See p.144 "Removing Staple Waste".

: Service Call indicator

Appears when the machine is malfunctioning or requires
maintenance.

: Open Cover indicator

Appears when the front cover, etc., is open.

Summary of Contents for AFICIO MP 6001
































































































































































Search results

Summary of Contents for AFICIO MP 6001

Reviews:

Related manuals for AFICIO MP 6001

Brands by name

Popular brands

Ricoh AFICIO MP 6001, Troubleshooting Manual

Search results

Summary of Contents for AFICIO MP 6001

Reviews:

Related manuals for AFICIO MP 6001

Brands by name

Popular brands